| 物品名称 |
规格型号 |
数量 |
单位 |
描述 |
| 槽刀 |
Φ125*Φ30*H30*4T |
6.00 |
个 |
{"规格":"Φ125*Φ30*H30*4T","齿数":"4","材质":"刀刃：合金钢"} |
| 槽刀 |
Φ125*Φ30*H40*4T |
6.00 |
个 |
{"规格":"Φ125*Φ30*H40*4T","齿数":"4","材质":"刀刃：合金钢"} |
| 新薄剪机圆刀 |
Ф80mm*Ф30mm*0.3mm |
500.00 |
片 |
{"规格型号":"Ф80mm*Ф30mm*0.3mm","尺寸":"尺寸： 外径80±1mm,内孔30+0.01mm到0.03mm,厚度0.3mm+0mm到0.02mm","角度":"8","平行度":"0.01","同心度":"0.05","刃口":"100倍高倍显微镜无缺口,缺口深度≤4微米,锯齿状缺口长度≤12微米,缺口数量≤2","外观要求":"刀口镜面,刀刃光滑锋利,无缺口,无碰伤,刀刃楔角8°","进口/国产":"国产","材质":"钨钢","孔间距":"0","特殊需求":"切边质量符合检验要求","参照标准":"GB/T 2078-2019","备注":"新薄剪机圆刀\\Ф80mm*Ф30mm*0.3mm\\尺寸： 外径80±1mm,内孔30+0.01mm到0.03mm,厚度0.3mm+0mm到0.02mm，\\8\\0.01\\0.05\\100倍高倍显微镜无缺口,缺口深度≤4微米,锯齿状缺口长度≤12微米,缺口数量≤2\\刀口镜面,刀刃光滑锋利,无缺口,无碰伤,国产\\钨钢\\0\\切边质量符合检验要求\\GB/T 2078-2019\\外径80±1mm,内孔30+0.01mm到0.03mm,厚度0.3mm+0到0.02mm,刀口镜面,刀刃光滑锋利,无缺口,无碰伤,刀刃\n楔角8°.国产/钨钢/易耗品,使用寿命:连续生产米数大于30000m.不合格品处理方式：刀片到货不得有裂纹，锈蚀，崩刃等缺陷，如不符合技术要求退货，造成损失由供货厂家全额承担"} |
| 维修厚剪圆盘刀上刀 |
120mm*170mm*2mm |
40.00 |
片 |
{"规格型号":"120mm*170mm*2mm","角度":"0","平行度":"0","同心度":"0","进口/国产":"国产","材质":"高速钢","孔间距":"0"} |
| 维修厚剪圆盘刀下刀 |
160mm*210mm*20mm |
20.00 |
片 |
{"规格型号":"160mm*210mm*20mm","角度":"0","平行度":"0","同心度":"0","进口/国产":"国产","材质":"高速钢","孔间距":"0"} |
| 刀盘 |
TRM16ACM6200R-M |
1.00 |
个 |
{"规格型号":"TRM16ACM6200R-M","材质":"原材铝合金材料7075径向/轴向 跳动0.02~0.03 5","强度及硬度要求":"≥HB140~150","参照标准":"GB/T 28247-2012","备注":"使用寿命：大于两年\n该到货产品与上述要求不符，对该到货产品进行10%处罚或调换。\n国际标准：ISO 14001：215"} |
| 动刀座 |
V800-02-001-06 |
200.00 |
套 |
{"规格型号":"V800-02-001-06","材质":"45号钢调质处理","使用寿命":"365天","参照标准":"JB/T 5936-2018","备注":"硬度：HB230-260\n适用设备名称：剪切式破碎机\n设备厂家：国产\n具体参数、尺寸可向技术人员索取图纸或现场测绘.\n要求产品到货包装完好、无破损，无锈蚀，如遇技术要求不符退换货处理。"} |
| 车刀片 |
WNMG080408-HA铝铜 |
30.00 |
个 |
{"规格型号":"WNMG080408-HA铝铜","刀片硬度":"HRC40-50","切削材料":"铝","刀尖材质":"硬质材料","刀身材质":"硬质材料","刃口":"完整无崩刃","外观要求":"完整无崩刃","进口/国产":"国产","孔间距":"5.16","特殊需求":"R≥0.8","验收":"如到货产品与上述要求不符，直接进行退货处理","使用寿命":"20天","参照标准":"GB/T 2080-2007"} |
| 刀头 |
VNMG160404-TMT9125 |
50.00 |
片 |
{"规格型号":"VNMG160404-TMT9125","刀片硬度":"HRA>90.5","材质":"硬质合金，表面涂层","尺寸":"长度16.6mm厚度4.76mm内孔直径3.81mm圆角0.4mm","角度":"35","参照标准":"JB/T 11442-2013","备注":"1.刀片通用性强，耐磨性高，可加工碳素钢、合金钢、铜、铝等.使用过程中涂层表面不允许有开裂、脱落现象\n2.使用寿命.连续切削大于4小时\n3.不合格处理标准.与要求不符，对该产品进行调换退货."} |
| 刀梁支架 |
E97.000524 |
2.00 |
个 |
{"规格型号":"E97.000524","材质":"酚醛树脂","使用寿命":"730天","特殊要求":"表面光滑无毛刺","参照标准":"GB/T 14486-2008","备注":"国产备件,支架厚度30mm,挡板尺寸厚度5mm半圆内为200mm*厚度160mm,详细尺寸见图纸尺寸,无品牌要求,到货备件满足尺寸要求均可,到货需出具合格证,包装完好无损,备件无破损,如果出现质量问题,厂家应及时给予退换货"} |
| 分切刀架总成 |
115*115*280 |
2.00 |
套 |
{"规格型号":"115*115*280","图纸号/备件号":"无","主要材质":"镍板、铝","适用设备":"分切机","设备型号":"Sepamat 18/10","品牌":"无","参照标准":"GB/T 2054-2013","备注":"1.不合格处理意见:到货后必须满足生产使用要求,如达不到使用要求退换货所产生的所有费用由卖家承担.\n2.使用寿命:≥2年.\n3.刀架下刀后刀片垂直无横纵向偏移，刀架横向纵向平移线性滑块运行顺畅，静止状态晃动无移动位，设备运行期间稳定不允许偏移.铝箔切边后切边位置平顺，此刀架总成为非标准件,参照标准执行金属切削刀具国家标准\n4.到货附带6mm，8mm，10mm刀板各四个，可现场测量."} |
| 硬质合金精车刀片 |
VCGT160404 |
20.00 |
片 |
{"规格型号":"VCGT160404","刀片硬度":"≥HRA80","切削材料":"钛合金/镍合金","刀尖材质":"钨钢硬质合金,TiALN涂层","刀身材质":"镍铬合金","刃口":"R0.4","外观要求":"无","进口/国产":"国产","孔间距":"无","特殊需求":"无","验收":"到货如与上述要求不符，供应商负责免费退换货，退换货过程中产生的费用由供应商承担。","使用寿命":"连续加工钛合金时间30分钟以上天","参照标准":"GB/T 2079-2015","备注":"无"} |
登录
微信在线客服